Heating and cooling controlled via a GSM gateway
Posted: Mon Nov 16, 2026 2:03 pm
I’ve been toying with this idea since the summer, when I had to crank the air conditioning and ventilation to 100% for at least 2–3 minutes every day before leaving work—just so I wouldn’t roast in the car on the way home (Leaving the windows cracked open by about 2 cm for the entire shift didn’t really help much either
) . And the final decision came only now, as winter begins, when I watched my wife from the window laboriously scraping frost off the windshield
.
I ordered this GSM gateway from AliExpress, made by WLTE Control. It features 4x changeover relays, 4x universal inputs, and 2x temperature sensors (it’s also available with a temperature and humidity sensor, but that seemed unnecessary to me).Specifically, the SM4-WLTE model for €65
As a first step, the wiring in the fuse box located in the engine compartment must be modified. In the original configuration, the air conditioning and heating can only be activated once the ignition key is turned to the second position and the "READY" indicator light illuminates—that is, after the main B+ contactor inside the fuse box has been engaged.
Unscrew both nuts on the contactor and remove the cable with a lug—marked in yellow—from the bottom terminal. You can screw the nut back on.
Next, attach this cable (with its lug) to the upper contact of the contactor and screw the nut back on. (Tighten the nuts firmly, but use COMMON SENSE! Firmly, because 250 to 320A of current flows through it. And with common sense, because the threaded insert is merely embedded within the contactor's plastic housing.)
We have now ensured that the HV power supply will be available once the B-contactor inside the battery engages.
The next step is to power up the vehicle using a 12V supply, which is needed to wake up the BMS, the climate control panel, and the fan. During the conversion process, I also discovered that a +12V feed is required for the heating contactors (the climate control panel grounds them to engage them; the +12V likely comes from the VMS once the B+ contactor in the fuse box has closed—presumably to ensure that high-voltage power isn't routed to the heater through the pre-charge resistor and pre-charge relay).
First, we prepare the GSM gateway itself, including the power supply for the unit and its peripherals, as well as the relay connections using the NO (Normally Open) contacts for relays 1, 2, and 3. I sourced the GND and Batt+12V connections from the connector—located on the right-hand side under the dashboard—where the original GSM gateway for the SharenGo system was previously connected. This circuit is protected by a 10A fuse located in the engine bay near the wiper motor, so no additional fusing is required.
The first step in the sequence for activating the car's heating/cooling system is to supply +12V to the BMS, which then engages the B- contactor within the battery. The best connection point for this is the wiring leading to a module that monitors the 12V battery voltage; if the voltage drops, this module activates the BMS, allowing the DC/DC converter to recharge the 12V battery even when the vehicle is switched off. This module is located near the fuse box under the steering wheel on the driver's side. It is a small, black, encapsulated unit containing a relay and a green LED, with four wires connected via a 4-pin connector: two white wires, one brown wire, and one red wire.
Cut the white wire numbered 1702 (I haven't verified whether this same number applies to all vehicles, but I assume it does); when viewed from the driver's side with the connector key facing upward, this wire is located at the top right.
Extend the cable EMERGING FROM THE CONNECTOR by soldering on an additional wire of the appropriate cross-section (approx. 1.5 m long) and connect it to the NC contact of the first relay.
Extend the cable coming FROM THE BUNDLE by soldering on a wire of the appropriate cross-section (approx. 1.5 m long) and connect it to the COM1 terminal of the first relay. Now, using the first GSM relay, we are able to switch on the power supply for the BMS, allowing it to engage the B- contactor of the HV system.
Once the HV power is switched on, the next step is to turn on the climate control panel. The +12V (switched via the ignition key) connects to the left-hand connector (when viewing the climate control panel from the rear)—specifically to the bottom-most pin on the far left, which is red. Cut the red wire and connect the cable leading TOWARDS THE CONNECTOR to relay no. 2 of the GSM gateway—specifically to COM2. Connect the cable leading TOWARDS THE WIRING HARNESS to the NC contact of relay no. 2. In reality, I actually connected it a bit further along than what is shown in the image above—specifically, past the point where I tapped the switched 12V (KEY+12V) signal for the seat heaters. This means that when the climate control panel turns on via the GSM module, the seat heaters turn on as well.
We are now able to activate the climate control panel using relay no. 2 of the GSM gateway. This modification is sufficient to cool the car using the air conditioning, but it does not yet allow us to heat the vehicle during the winter.
To avoid having to manually turn off the heater via a mobile app every time it starts, and to ensure the operation stops automatically when the ignition key is turned, the GSM gateway is equipped with programmable inputs. These inputs are "pull-up" type, meaning they must be connected to GND (ground) to be triggered. However, the ignition key signal (KEY) is +12V; therefore, we can use four PC817 optocouplers, along with four 1.8kΩ resistors, to interface this. I used the first input to monitor the charging of the 12V battery via the "black box" mentioned earlier (apparently, this unit is called TUDOR), and the second input to monitor the activation of the ignition switch. Two additional inputs are reserved for your applications, just like relay number 4.
I routed temperature sensor 1 through a grommet into the engine bay and positioned it between the fender and the washer fluid reservoir, securing it so that it hangs 10 cm away from any surfaces; it serves as an external temperature sensor.
I routed temperature sensor 2 in a similar fashion to the area beneath the dashboard—specifically below the climate control panel—ensuring it hangs freely in the air without touching anything; this is used to monitor the temperature inside the vehicle.
If your only goal is to cool the vehicle, you can consider the modification complete at this stage.
I am continuously editing and adding to the article .......
I ordered this GSM gateway from AliExpress, made by WLTE Control. It features 4x changeover relays, 4x universal inputs, and 2x temperature sensors (it’s also available with a temperature and humidity sensor, but that seemed unnecessary to me).Specifically, the SM4-WLTE model for €65
As a first step, the wiring in the fuse box located in the engine compartment must be modified. In the original configuration, the air conditioning and heating can only be activated once the ignition key is turned to the second position and the "READY" indicator light illuminates—that is, after the main B+ contactor inside the fuse box has been engaged.
Unscrew both nuts on the contactor and remove the cable with a lug—marked in yellow—from the bottom terminal. You can screw the nut back on.
Next, attach this cable (with its lug) to the upper contact of the contactor and screw the nut back on. (Tighten the nuts firmly, but use COMMON SENSE! Firmly, because 250 to 320A of current flows through it. And with common sense, because the threaded insert is merely embedded within the contactor's plastic housing.)
We have now ensured that the HV power supply will be available once the B-contactor inside the battery engages.
The next step is to power up the vehicle using a 12V supply, which is needed to wake up the BMS, the climate control panel, and the fan. During the conversion process, I also discovered that a +12V feed is required for the heating contactors (the climate control panel grounds them to engage them; the +12V likely comes from the VMS once the B+ contactor in the fuse box has closed—presumably to ensure that high-voltage power isn't routed to the heater through the pre-charge resistor and pre-charge relay).
First, we prepare the GSM gateway itself, including the power supply for the unit and its peripherals, as well as the relay connections using the NO (Normally Open) contacts for relays 1, 2, and 3. I sourced the GND and Batt+12V connections from the connector—located on the right-hand side under the dashboard—where the original GSM gateway for the SharenGo system was previously connected. This circuit is protected by a 10A fuse located in the engine bay near the wiper motor, so no additional fusing is required.
The first step in the sequence for activating the car's heating/cooling system is to supply +12V to the BMS, which then engages the B- contactor within the battery. The best connection point for this is the wiring leading to a module that monitors the 12V battery voltage; if the voltage drops, this module activates the BMS, allowing the DC/DC converter to recharge the 12V battery even when the vehicle is switched off. This module is located near the fuse box under the steering wheel on the driver's side. It is a small, black, encapsulated unit containing a relay and a green LED, with four wires connected via a 4-pin connector: two white wires, one brown wire, and one red wire.
Cut the white wire numbered 1702 (I haven't verified whether this same number applies to all vehicles, but I assume it does); when viewed from the driver's side with the connector key facing upward, this wire is located at the top right.
Extend the cable EMERGING FROM THE CONNECTOR by soldering on an additional wire of the appropriate cross-section (approx. 1.5 m long) and connect it to the NC contact of the first relay.
Extend the cable coming FROM THE BUNDLE by soldering on a wire of the appropriate cross-section (approx. 1.5 m long) and connect it to the COM1 terminal of the first relay. Now, using the first GSM relay, we are able to switch on the power supply for the BMS, allowing it to engage the B- contactor of the HV system.
Once the HV power is switched on, the next step is to turn on the climate control panel. The +12V (switched via the ignition key) connects to the left-hand connector (when viewing the climate control panel from the rear)—specifically to the bottom-most pin on the far left, which is red. Cut the red wire and connect the cable leading TOWARDS THE CONNECTOR to relay no. 2 of the GSM gateway—specifically to COM2. Connect the cable leading TOWARDS THE WIRING HARNESS to the NC contact of relay no. 2. In reality, I actually connected it a bit further along than what is shown in the image above—specifically, past the point where I tapped the switched 12V (KEY+12V) signal for the seat heaters. This means that when the climate control panel turns on via the GSM module, the seat heaters turn on as well.
We are now able to activate the climate control panel using relay no. 2 of the GSM gateway. This modification is sufficient to cool the car using the air conditioning, but it does not yet allow us to heat the vehicle during the winter.
To avoid having to manually turn off the heater via a mobile app every time it starts, and to ensure the operation stops automatically when the ignition key is turned, the GSM gateway is equipped with programmable inputs. These inputs are "pull-up" type, meaning they must be connected to GND (ground) to be triggered. However, the ignition key signal (KEY) is +12V; therefore, we can use four PC817 optocouplers, along with four 1.8kΩ resistors, to interface this. I used the first input to monitor the charging of the 12V battery via the "black box" mentioned earlier (apparently, this unit is called TUDOR), and the second input to monitor the activation of the ignition switch. Two additional inputs are reserved for your applications, just like relay number 4.
I routed temperature sensor 1 through a grommet into the engine bay and positioned it between the fender and the washer fluid reservoir, securing it so that it hangs 10 cm away from any surfaces; it serves as an external temperature sensor.
I routed temperature sensor 2 in a similar fashion to the area beneath the dashboard—specifically below the climate control panel—ensuring it hangs freely in the air without touching anything; this is used to monitor the temperature inside the vehicle.
If your only goal is to cool the vehicle, you can consider the modification complete at this stage.
I am continuously editing and adding to the article .......